Easy IP with Starlink & Unifi Networks: Technical FAQ Easy IP
Easy IP Starlink Unifi integration solves common networking challenges by providing static IP access without creating problematic double NAT configurations. This technical guide covers network topology solutions for all Starlink generations while maintaining your existing Unifi infrastructure.
👆 Network Diagram Image | Starlink Static Public IP Address from Easy IP with Unify device.
Easy IP Starlink Unifi Network Architecture & Double NAT Concerns
Q: Can I use Easy IP with my existing Starlink and Unifi setup without creating problematic NAT layers?
A: Yes, Easy IP Starlink Unifi configurations avoid problematic double NAT by using proper network topology:
For Starlink Gen 3 (2 Ethernet ports):
- Leave Starlink router in normal operating mode (192.168.1.x)
- Connect Unifi UDM/Gateway to Port 1 for general network traffic
- Connect Easy IP HapAX to Port 2 for devices requiring static IP access
- Creates clean network separation with optimal routing
For Starlink Gen 1/Gen 2 (1 Ethernet port):
- Custom configuration with bridged WAN ports
- Single input from Starlink connects to Easy IP device
- Two bridged ports allow both Unifi and Easy IP connections on WAN side
- Prevents forcing general traffic through public IP tunnel
Q: What network addressing scheme should I use?
A: Recommended IP allocation:
- Starlink Network: 192.168.1.x (default)
- Easy IP Network: 192.168.10.x (CCTV/cameras)
- Unifi Network: 192.168.5.x (general devices)
This prevents IP conflicts and enables proper traffic routing based on device requirements.
Device Configuration & Traffic Routing
Q: How does Easy IP selectively route only specific device traffic through the static IP?
A: Easy IP Starlink Unifi setups use NetPanel’s intelligent routing system:
- Access Control Lists (ACL): Define which devices must use public IP
- Static DHCP Reservations: Convert dynamic leases to static with one click
- Selective Routing Rules: Only ACL-defined devices use public IP tunnel
- Default Route: All other traffic uses fastest path (direct Starlink)
Example Easy IP Starlink Unifi Configuration:
- Camera 1 (192.168.10.100) → Always uses static public IP
- Camera 2 (192.168.10.101) → Always uses static public IP
- NVR (192.168.10.102) → Always uses static public IP
- All Unifi devices → Direct Starlink route (faster)
Q: Do I need Single WAN or Dual WAN Easy IP configuration?
A: Depends on your requirements:
Single WAN:
- Sufficient for Gen 3 Starlinks with dual ports
- Handles CCTV static IP requirements
- Most cost-effective option
Dual WAN:
- Required for automatic failover between connections
- Useful with 4G backup alongside Starlink
- Seamless IP address transition during connection switching
Easy IP Starlink Unifi integration with existing infrastructure:
Q: Will this disrupt my existing Unifi cloud controller setup?
A: No disruption to existing infrastructure:
- Unifi devices continue using existing network paths
- Cloud controllers remain unchanged
- WiFi, switches, and access points function normally
- Easy IP operates as separate network segment for specific devices only
Q: How do I configure port forwarding for cameras through the static IP?
A: Via NetPanel cloud management:
- Device Discovery: Easy IP detects connected devices via DHCP
- Static Reservation: Convert camera DHCP lease to static assignment
- Port Mapping: Define external ports → internal device:port mappings
- ACL Assignment: Add device to public IP access control list
Example:
- External Port 8080 → Camera 1 (192.168.10.100:80)
- External Port 8081 → Camera 2 (192.168.10.101:80)
- External Port 8082 → NVR Web Interface (192.168.10.102:80)
Performance & Routing Optimization
Q: Does all network traffic get forced through the public IP tunnel?
A: No, Easy IP Starlink Unifi networks ensure optimal performance through selective routing. Only designated devices use the public IP:
Public IP Route (Higher Latency):
- CCTV cameras and NVR systems
- Devices requiring external accessibility
- Traffic defined in access control lists
Direct Starlink Route (Lower Latency):
- General internet browsing
- WiFi client traffic
- Software updates and streaming
- All non-ACL traffic
This ensures optimal performance for general network usage while providing static IP access where needed.
Q: Can the static IP reach devices on the Unifi network?
A: No, by design:
- Easy IP static IP only provides access to Easy IP LAN segment (192.168.10.x)
- Unifi network (192.168.5.x) remains isolated and secure
- Cross-network access requires specific routing rules if needed
- This isolation is a security benefit, not a limitation
Hardware Requirements & Custom Configurations
Q: What hardware modifications are available for single-port Starlinks?
A: Custom bridge configuration:
- Input: Single Ethernet from Starlink adapter
- Output: Two bridged WAN ports
- Port 1: Connects to Unifi equipment (WAN-side connection)
- Port 2: Continues to Easy IP device for static IP services
- Result: No additional NAT layer, optimal traffic flow
Q: How does failover work in dual WAN configurations?
A: Automatic failover process:
- Primary Connection: Starlink provides main internet access
- Secondary Connection: 4G/5G router as backup
- Monitoring: Continuous connection health checks
- Switchover: Automatic transition maintains static IP address
- Recovery: Automatic failback when primary connection restored
Key Benefit: Static IP address remains constant regardless of which WAN connection is active.
Technical Specifications
Q: What are the network performance characteristics?
A:
- Latency: London data centre connectivity for optimal UK performance
- Throughput: No artificial limitations on static IP traffic
- Reliability: Carrier-independent IP addressing
- Compatibility: Works with all Starlink service tiers
Q: How does this compare to Starlink Business Priority static IP?
A: Technical comparison:
| Feature | Easy IP Solution âś… | Starlink Business |
| Static IP | Carrier independent | Starlink network only |
| Flexibility | Works with any Starlink tariff | Requires business plan |
| Management | Cloud-based NetPanel | Starlink app only |
| Failover | Multi-carrier support | Starlink network only |
| Traffic Control | Selective device routing | All-or-nothing |
Network Troubleshooting
Q: How do I verify traffic is routing correctly?
A: Easy IP Starlink Unifi Verification methods:
- IP Address Check: Confirm cameras show static public IP when accessing external services
- Trace Route: Verify camera traffic goes through SimRush data centre
- Speed Tests: Confirm general devices use direct Starlink route (faster speeds)
- NetPanel Monitoring: Real-time traffic statistics and routing information
Q: What happens if the Easy IP device goes offline?
A:
- CCTV Access: Remote access to cameras will be unavailable
- Local Access: Cameras remain accessible on local network (192.168.10.x)
- General Network: Unifi devices continue working normally via Starlink
- Recovery: Device automatically reconnects when power/connectivity restored
